CCNA: ICND2: Interconnecting Cisco Networking Devices Part 2 v3.0

Duration: 5 days

A new version of this course, ICND2 v2.0, is available now and is part of Cisco's new CCNA Routing and Switching certification program. Building on the skills provided by ICND1 (Interconnecting Cisco Network Devices 1), ICND2 not only delivers essential information needed to pass the CCNA certification exams, it also gives you a solid technical foundation to ensure that you can succeed on the job

Interested in attending? Have a suggestion about running this course near you?
Register your interest now

Description

Course Outline

Lesson 1. Small Network Implementation
Lesson 2. Medium-Sized Switched Network Construction
• VLANs and Trunks
• Spanning Tree Performance Optimization
• Routing Between VLANs
• Securing the Expanded Network
• Troubleshooting Switched Networks
Lesson 3. Medium-Sized Routed Network Construction
• Routing Operations
• Implementing VLSM
Lesson 4. Single-Area Open Shortest Path First (OSPF)
• Implementing OSPF
• Troubleshooting OSPF
Lesson 5. Enhanced Interior Gateway Routing Protocol (EIGRP)
• Implementing EIGRP
• Troubleshooting EIGRP
Lesson 6. Access Control Lists (ACLs)
• ACL Operation
• Configuring and Troubleshooting ACLs
Lesson 7. Address Space Management
• Scaling the Network with NAT and PAT
• Transitioning to IPv6
Lesson 8. LAN Extension into a WAN
• VPN Solutions
• Establishing a Point-to-Point WAN Connection with PPP
• Establishing a WAN Connection with Frame Relay
• Troubleshooting Frame Relay WANs
Lab Outline
Lab 1: Implementing a Small Network (Review Lab)
Configure your workgroup switch and router with a basic configuration based on the network information provided.
Lab 2: Configuring Expanded Switch Networks
Expand the switch configuration to meet specific VLAN and network requirements.
Lab 3: Troubleshooting Switched Networks
Use troubleshooting methods discussed to diagnose, isolate, and correct problems commonly found in a switched network.
Lab 4: Implementing OSPF
Configure your workgroup routers to use the dynamic routing protocol OSPF.
Lab 5: Troubleshooting OSPF
Use troubleshooting methods discussed to diagnose, isolate, and correct problems commonly found when running the OSPF routing protocol.
Lab 6: Implementing EIGRP
Configure your workgroup routers to migrate from OSPF to EIGRP.
Lab 7: Troubleshooting EIGRP
Use troubleshooting methods discussed to diagnose, isolate, and correct problems commonly found when running the EIGRP routing protocol.
Lab 8: Implementing ACLs
Create IP standard, extended, and named ACLs and verify that they are working
Lab 9: Troubleshooting ACLs
Troubleshoot common IP ACL issues.
Lab 10: Enhanced - Configuring Network Address Translation (NAT) and Port Address Translation (PAT)
Configure your workgroup routers to use static and dynamic NAT and PAT.
Lab 11: Implementing IPv6
Configure IPv6 addresses on your workgroup routers and deploy RIPng between them.
Lab 12: Establishing a Frame Relay WAN
Create a Frame Relay connection to the other pod router and to the core router using a serial interface on each pod router.
Lab 13: Troubleshooting Frame Relay WANs
Use troubleshooting methods discussed to diagnose, isolate, and correct problems commonly found in a Frame Relay network.
Lab 14: Rebuild the configuration on the pod devices from scratch, including security, IP addressing, interface encapsulations, and routing protocol.

Prerequisites

ICND1 (Interconnecting Cisco Network Devices 1)

Target audience

 

Network technicians and specialists looking to increase their knowledge of medium-sized switched and routed networks

 

Anyone looking to achieve CCNA certification

Do NOT follow this link or you will be banned from the site!